Revolutionize Your Ride with the DialDim™ Lighting Controller

Take control of your auxiliary lighting like never before with DENALI's groundbreaking DialDim™ Lighting Controller. This innovative device puts unparalleled power at your fingertips, allowing you to manage two sets of lights independently with a single, intuitive interface.

Built for the Long Haul

Engineered for the demands of powersports, the DialDim™ Controller boasts a fully waterproof design. Gaskets and o-rings at every joint ensure reliable operation in all weather conditions. The controller's rugged construction is matched by its smart internals, featuring electronically fused circuits that protect your lighting system and vehicle electrical components.

Intelligent Illumination at Your Command

The DialDim™ Controller features a multicolor halo dimming switch that displays your exact settings in real-time. With eight intensity levels per circuit, you can fine-tune your lighting to match any riding condition. The blue halo controls light set one, while the green halo manages light set two – simply double-click to switch between circuits.

Safety-Enhancing Smart Features

Our lighting controller goes beyond basic on/off functionality. It integrates seamlessly with your vehicle's systems, offering intelligent flash features that enhance your visibility and safety on the road. Cancel your aux lights with your turn signal, flash them as additional turn indicators, or create attention-grabbing strobes when you sound your horn.

More Features, More Feedback!

Our patent-pending multicolor halo dimmer switch can do a whole lot more than just turn your lights on and off and dim them. For starters, it displays the exact intensity of both of your lights so you're never stuck guessing if your lights are on, or what intensity they're set to.

Thanks to the electronically fused circuits, the halo switch can also display, and allow you to select, the fuse values for each circuit. And if a fuse trips, the LED halo will turn red providing real-time feedback and allow for resetting the fuse.

Last but not least, the switch halo doubles as a battery monitor with a low-voltage cutoff feature. Our industry-first design will flash different colors on startup to display your battery health and automatically shut off your auxiliary lights if the battery voltage drops below 10.8 volts.

More Than Just a Switch

The DialDim™ isn't just a lighting controller – it's your onboard electrical assistant. It monitors your battery health, displaying voltage status on startup and implementing a low-voltage cutoff to prevent you from being stranded. The multicolor halo switch even allows you to select and display fuse values for each circuit, providing real-time feedback on your system's status.

Versatile Mounting Options

Designed for easy installation, the DialDim™ comes with a 7/8" handlebar mount, making it a perfect fit for most motorcycles. The 72" switch lead provides ample length for custom mounting solutions, with an optional 48" extension available for larger vehicles or unique setups.

Unlock Your Lighting's Full Potential

With the DialDim™ Lighting Controller, you're not just adding lights to your ride – you're adding intelligence. Experience the next level of lighting control, where safety meets performance in a compact, user-friendly package. Ride smarter, ride safer, and light up the road ahead with DENALI.

The controller housing and switch both feature a fully waterproof design with gaskets and o-rings at every joint to ensure hassle-free operation in outdoor environments. 

Features

• ON/OFF & Dim - Independently control two sets of lights on/off and intensity level using the single DialDim™ Switch. The blue halo controls light set one and the green halo controls light set two. Double click to switch between the two circuits.
• High/Low Sync - Your auxiliary lights will automatically switch between your selected dim setting to full intensity with the factory high beam switch. Simply connect the blue input wire to your vehicle's high beam circuit to enable this feature.
• Stealth Mode - A clever 0% dim setting on the switch allows your lights to be "off" during normal driving conditions but will jump to 100% intensity with your vehicle's high beam switch. The lights will also react to turn signal and horn inputs in this mode but will remain off when no inputs are detected.
• Cancel with Turn Signal - When enabled the main lights (blue circuit 1) will cancel in sync with your signal to prevent "washing out" your factory turn signal. Simply connect the yellow and orange input wires to your vehicle turn signal circuit to enable this feature.
• Flash as Turn Signal - When enabled your amber visibility lights (green circuit 2) will flash in sync with your factory turn signals. Simply connect the yellow and orange input wires to your vehicle turn signal circuit to enable this feature.
• Strobe with Horn - When enabled your auxiliary lights on both circuits will strobe at 4Hz when you sound your horn. Simply connect the green input wire to your vehicle horn circuit to enable this feature.
• Electronically Fused Circuits - Both light circuits are electronically fused and can be set right from the switch itself! The halo will illuminate red to notify you when a circuit fused is tripped.
• Voltage Display Indicator - Upon vehicle startup, the switch halo will flash green to indicate a healthy battery voltage, or flash red to indicate a battery voltage that is below 11.8v.
• Low Voltage Cutoff - If the battery voltage drops below 10.8v the lights will not power on preventing you from being stranded. The switch halo will flash 4 red LEDs to indicate the low voltage condition.

*To enable high-beam, turn signal, and horn related functions you need to connect to a clean 12v circuit on your vehicle. To disable these features simply do not connect to the corresponding vehicle circuit.  

Click HERE to learn more about the features and operation of the DialDim™ Switch

Product Specs 

• Two fully independent light circuits 
• Eight intensity levels per circuit (5%, 15%, 30%, 45%, 60%, 75%, 100%)
• Eight electronic fuse values (1A, 2A, 4A, 6A, 8A, 10A, 15A, 20A)
• Five feature input wires (ignition, high beam, horn, left turn, right turn) 
• 20A max per circuit (30A max combined) 
• Operating Voltage: 12 VDC

What’s In The Box?

• (1x) DialDim™ Controller Harness 
• (1x) DialDim™ Multi-function Switch 
• (1x) 7/8" Handlebar Switch Mount
• (4x) 66" Plug-&-Play Light Extensions  
• (1x) Universal Input Trigger Wire Harness 
  
  

Note:  The length of the switch lead is 72", a 48" Switch Extension is available for purchase separately.

Instruction Manual Download

• PDF Instruction Manual (English)